DOP of 12 months

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1   General
(1)   This EN provides a design method for fastenings (connection of structural elements and non-structural elements to structural components), which are used to transmit actions to the concrete.
Inserts embedded in precast concrete elements during production, under Factory Production Control (FPC) conditions and with the due reinforcement, intended for use only during transient situations for lifting and handling, are covered by the CEN/TR “Design and Use of Inserts for Lifting and Handling Precast Concrete Elements”, by CEN/TC 229.
(2)   This EN is intended for safety related applications in which the failure of fastenings will result in collapse or partial collapse of the structure, cause risk to human life or lead to significant economic loss.  In this context it also covers non-structural elements.
(3)   The support of the fixture may be either statically determinate or statically indeterminate. Each support may consist of one fastener or a group of fasteners.
(4)   This EN is valid for applications which fall within the scope of the series EN 1992. In applications where special considerations apply, e.g. nuclear power plants or civil defence structures, modifications may be necessary. The transmission of the fastener loads to the supports of the concrete member shall be shown for the ultimate limit state and the serviceability limit state according to EN 1992-1-1.
(5)   This EN does not cover the design of the fixture. The design of the fixture shall be carried out to comply with the appropriate Standards.
(6)   This document relies on characteristic resistances and distances which are stated in a European Technical Product Specification (see Annex E). At least the characteristics of Annex E, Table E.1 should be given in a European Technical Product Specification providing a basis for the design methods of this EN.
1.2   Type of fasteners and fastening groups
(1)   This EN uses the fastener design theory ) (Figure 1.1) and applies to:
a)   cast-in fasteners such as headed fasteners, anchor channels with rigid connection between anchor and channel;
b)   post-installed mechanical fasteners such as expansion anchors, undercut anchors and concrete screws;
c)   post-installed bonded anchors, bonded expansion anchors and bonded undercut anchors.
NOTE   Connections with post-installed ribbed reinforcing bars should be covered by a European Technical Product Specification and comply with the requirements of EN 1992-1-1.
(2)   For other types of fasteners modifications of the design provisions may be necessary.
(3)   This EN applies to fasteners with established suitability for the specified application in concrete covered by provisions, which refer to this EN and provide data required by this EN. The suitability of the fastener is stated in the relevant European Technical Product Specification.
(...)
(4)   This EN applies to single fasteners and groups of fasteners. In a fastening group the loads are applied to the individual fasteners of the group by means of a common fixture. In this EN it is assumed that in a fastener group only fasteners of the same type and size are used.
The configurations of fastenings with cast-in place headed fasteners and post-installed fasteners covered by this EN are shown in Figure 1.2.
For anchor channels the number of fasteners is not limited.
(...)
NOTE   Configuration with three fasteners is not recommended close to an edge (ci < 100mm) as there are no safe design models for shear loads.
1.3   Fastener dimensions and materials
(1)   This EN applies to fasteners with a minimum diameter or a minimum thread size of 6 mm (M6) or a corresponding cross section. In general, the effective embedment depth should be: hef  40 mm. The actual value for a particular fastener shall be taken from the relevant European Technical Product Specification. In case of post-installed chemical fasteners the effective embedment depth is limited to hef  20dnom. (....)

  • Standard
    129 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1   General
(1) This European Standard provides a design method for fastenings (connection of structural elements and non-structural elements to structural components), which are used to transmit actions to the concrete. This design method uses physical models which are based on a combination of tests and numerical analysis consistent with EN 1990:2002, 5.2.
The requirements for the transmission of the fastener loads within the concrete member to its supports are given in EN 1992-1-1 and Annex A of this EN.
Inserts embedded in precast concrete elements during production, under Factory Production Control (FPC) conditions and with the due reinforcement, intended for use only during transient situations for lifting and handling, are covered by CEN/TR 15728.
(2) This EN is intended for safety related applications in which the failure of fastenings may result in collapse or partial collapse of the structure, cause risk to human life or lead to significant economic loss. In this context it also covers non-structural elements.
(3) The support of the fixture can be either statically determinate or statically indeterminate. Each support can consist of one fastener or a group of fasteners.
(4) This EN is valid for applications which fall within the scope of the EN 1992 series. In applications where special considerations apply, e.g. nuclear power plants or civil defence structures, modifications can be necessary.
(5) This EN does not cover the design of the fixture. The requirements for the design of the fixture are given in the appropriate Standards and fulfil the requirements on the fixture as given in this EN.
(6) This document relies on characteristic resistances and distances which are stated in a European Technical Product Specification (see Annex E). At least the characteristics of Annex E are given in a European Technical Product Specification for the corresponding loading conditions providing a basis for the design methods of this EN.
NOTE   The numerical values for certain parameters given in Notes can be used for pre-dimensioning. The values for verification are given in the European Technical Product Specifications and may be different.
1.2   Type of fasteners and fastening groups
(1)   This EN uses the fastener design theory ) (see Figure 1.1) and applies to:
a)   cast-in fasteners such as headed fasteners, anchor channels with rigid connection (e.g. welded, forged) between anchor and channel;
b)   post-installed mechanical fasteners such as expansion fasteners, undercut fasteners and concrete screws;
c)   post-installed bonded fasteners and bonded expansion fasteners.
(2)   For other types of fasteners modifications of the design provisions can be necessary.
(3)   This EN applies to fasteners with established suitability for the specified application in concrete covered by provisions, which refer to this EN and provide data required by this EN. The suitability of the fastener is stated in the relevant European Technical Product Specification.
(...)
(4)   This EN applies to single fasteners and groups of fasteners. In a group of fasteners the loads are applied to the individual fasteners of the group by means of a common fixture. In a group of fasteners this European Standard applies only if fasteners of the same type and size are used.
(5)   The configurations of fastenings with cast-in place headed fasteners and post-installed fasteners covered by this EN are shown in Figure 1.2.
(6)   For anchor channels the number of anchors is not limited.
(...)
(7)   Post-installed ribbed reinforcing bars used to connect concrete members are covered by a European Technical Product Specification. This EN applies when connections are designed in accordance with EN 1992-1-1.
1.3   Fastener dimensions and materials
(1)   This EN applies to fasteners with a minimum diameter or a minimum thread size of 6 mm (M6) or a corresponding cross section. (....)

  • Standard
    129 pages
    English language
    sale 10% off
    e-Library read for
    1 day

DOP of 12 months!

  • Amendment
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day

DOP of 12 months!

  • Amendment
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

DOP of 12 months! * 2017-03-22 FJD - No xml version as mother version was not originally published as xml.

  • Amendment
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day

DOP of 12 months!
2017-03-29 FJD - No xml version as the mother standard EN 1993-4-2:2007 was not edited as an xml deliverable.

  • Amendment
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Assessment of loads imposed by snow to be used in the structural design of buildings and civil engineering works on sites at altitudes below 1500 m.

  • Amendment
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Assessment of loads imposed by snow to be used in the structural design of buildings and civil engineering works on sites at altitudes below 1500 m.

  • Amendment
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day

General rules for the structural design of buildings and civil engineering works in reinforced and prestressed concrete made with normal and lightweight aggregates, plain or lightly reinforced concrete and precast concrete for the design of reinforced concrete components with unbonded tendons.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

General rules for the structural design of buildings and civil engineering works in reinforced and prestressed concrete made with normal and lightweight aggregates, plain or lightly reinforced concrete and precast concrete for the design of reinforced concrete components with unbonded tendons.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

General rules for the structural design of buildings and civil engineering works made of timber and/or wood-based panels, either singly or compositely with concrete, steel or other materials. Detailed rules for structural design of buildings.

  • Amendment
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Part 1-1 gives generic detailed strength rules which are applicable to steel structures in general. Their use and any limits of applicability are explained in the text where necessary. It does not cover resistance to fire; particular aspects of special types of buildings and civil engineering works (e.g. bridges, masts, silos, piling or off-shore structures).

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

EN 1991-1-7 provides strategies and rules for safeguarding buildings and other civil engineering works against identifiable and unidentifiable accidental actions. EN 1991-1-7 defines: - strategies based on identified accidental actions, - strategies based on limiting the extent of localised failure. The following subjects are dealt with in this part of EN 1991: - definitions and symbols (Section 1); - classification of actions (Section 2); - design situations (Section 3); - impact (Section 4); - explosions (Section 5); - design for consequences of localised failure in buildings from an unspecified cause (informative Annex A); - information on risk assessment (informative Annex B); - dynamic design for impact (informative Annex C); - internal explosions (informative Annex D). Rules on dust explosions in silos are given in EN 1991-4. Rules on impact from vehicles travelling on the bridge deck are given in EN 1991-2. EN 1991-1-7 does not specifically deal with accidental actions caused by external explosions, warfare and terrorist activities, or the residual stability of buildings or other civil engineering works damaged by seismic action or fire, etc.

  • Amendment
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Assessment of actions arising from accidental human activity including impact and collisions from wheeled vehicles, ships, derailed trains and helicopters on roofs and gas explosions in buildings - their analysis and determination of design values to be used in the structural design of buildings and civil engineering works. Procedures for risk analysis and technical measures to reduce consequences.

  • Amendment
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

General rules for the structural design of buildings and civil engineering works made of timber and/or wood-based panels, either singly or compositely with concrete, steel or other materials. Detailed rules for structural design of buildings.

  • Amendment
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Part 1-1 gives generic detailed strength rules which are applicable to steel structures in general. Their use and any limits of applicability are explained in the text where necessary. It does not cover resistance to fire; particular aspects of special types of buildings and civil engineering works (e.g. bridges, masts, silos, piling or off-shore structures).

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Supplementary to Part 1-1. Additional and varied rules to be used for the design of composite structures which are required to avoid premature structural collapse and to limit the spread of fire in the accidental situation of exposure to fire.

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day

EN 1999 applies to the design of buildings and civil engineering and structural works in aluminium. It complies with the principles and requirements for the safety and serviceability of structures, the basis of their design and verification that are given in EN 1990 - Basis of structural design. EN 1999 is only concerned with requirements for resistance, serviceability, durability and fire resistance of aluminium structures. Other requirements, e.g. concerning thermal or sound insulation, are not considered. EN 1999 is intended to be used in conjunction with: - EN 1990 "Basis of structural design" - EN 1991 "Actions on structures" - European Standards for construction products relevant for aluminium structures - prEN 1090-1: Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components5 - prEN 1090-3: Execution of steel structures and aluminium structures - Part 3: Technical requirements for aluminium structures5 EN 1999 is subdivided in five parts: EN 1999-1-1 Design of Aluminium Structures: General structural rules. EN 1999-1-2 Design of Aluminium Structures: Structural fire design. EN 1999-1-3 Design of Aluminium Structures: Structures susceptible to fatigue. EN 1999-1-4 Design of Aluminium Structures: Cold-formed structural sheeting. EN 1999-1-5 Design of Aluminium Structures: Shell structures.

  • Amendment
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day

(1) EN 1997-1 is intended to be used as a general basis for the geotechnical aspects of the design of buildings and civil engineering works.
(2) The following subjects are dealt with in EN 1997-1:
Section 1: General
Section 2: Basis of geotechnical design
Section 3: Geotechnical data
Section 4: Supervision of construction, monitoring and maintenance
Section 5: Fill, dewatering, ground improvement and reinforcement
Section 6: Spread foundations
Section 7: Pile foundations
Section 8: Anchorages
Section 9: Retaining structures
Section 10: Hydraulic failure
Section 11: Overall stability
Section 12: Embankments
(3) EN 1997-1 is accompanied by Annexes A to J, which provide:
- in A: recommended partial safety factor values; different values of the partial factors may be set by the National annex;
- in B to J: supplementary informative guidance such as internationally applied calculation methods.

  • Amendment
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Supplementary to Part 1-1. Additional and varied rules to be used for the design of composite structures which are required to avoid premature structural collapse and to limit the spread of fire in the accidental situation of exposure to fire.

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day

(1)   EN 1999-1-1 gives basic design rules for structures made of wrought aluminium alloys and limited guidance for cast alloys (see section 3).
NOTE   Minimum material thickness may be defined in the National Annex. The following limits are recommended – if not otherwise explicitly stated in this standard:
-   components with material thickness not less than 0,6 mm;
-   welded components with material thickness not less than 1,5 mm;
-   connections with:
o   steel bolts and pins with diameter not less than 5 mm;
o   aluminium bolts and pins with diameter not less than 8 mm;
o   rivets and thread forming screws with diameter not less than 4,2 mm
(2)   The following subjects are dealt with in EN 1999-1-1:
Section 1:   General
Section 2:   Basis of design
Section 3:   Materials
Section 4:   Durability
Section 5:   Structural analysis
Section 6:   Ultimate limit states for members
Section 7:   Serviceability limit states
Section 8:   Design of joints
Annex A    Execution classes
Annex B   Equivalent T-stub in tension
Annex C    Materials selection
Annex D   Corrosion and surface protection
Annex E    Analytical models for stress strain relationship
Annex F    Behaviour of cross section beyond elastic limit
Annex G    Rotation capacity
Annex H    Plastic hinge method for continuous beams
Annex I    Lateral torsional buckling of beams and torsional or flexural-torsional buckling of compression members
Annex J    Properties of cross sections
Annex K    Shear lag effects in member design
Annex L    Classification of connections
Annex M   Adhesive bonded connections
(3)   Sections 1 to 2 provide additional clauses to those given in EN 1990 “Basis of structural design”.
(4)   Section 3 deals with material properties of products made of structural aluminium alloys.
(5)   Section 4 gives general rules for durability.
(6)   Section 5 refers to the structural analysis of structures, in which the members can be modelled with sufficient accuracy as line elements for global analysis.
(7)   Section 6 g

  • Amendment
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day

TC - Modifications from EN 1998-3:2005/AC:2010 on the English mother reference version regarding the "National annex for EN 1998-3", Clauses 2 and 4 and Annexes A, B and C + New modifications in Annex A.

  • Corrigendum
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

(1) EN 1997-1 is intended to be used as a general basis for the geotechnical aspects of the design of buildings and civil engineering works.
(2) The following subjects are dealt with in EN 1997-1:
Section 1: General
Section 2: Basis of geotechnical design
Section 3: Geotechnical data
Section 4: Supervision of construction, monitoring and maintenance
Section 5: Fill, dewatering, ground improvement and reinforcement
Section 6: Spread foundations
Section 7: Pile foundations
Section 8: Anchorages
Section 9: Retaining structures
Section 10: Hydraulic failure
Section 11: Overall stability
Section 12: Embankments
(3) EN 1997-1 is accompanied by Annexes A to J, which provide:
- in A: recommended partial safety factor values; different values of the partial factors may be set by the National annex;
- in B to J: supplementary informative guidance such as internationally applied calculation methods.

  • Amendment
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Eurocode 6 applies to the design of buildings and civil engineering works, or parts thereof, in unreinforced, reinforced, prestressed and confined masonry. Eurocode 6 deals only with the requirements for resistance, serviceability and durability of structures. Other requirements, for example, concerning thermal or sound insulation, are not considered. Execution is covered to the extent that is necessary to indicate the quality of the construction materials and products that should be used and the standard of workmanship on site needed to comply with the assumptions made in the design rules. Eurocode 6 does not cover the special requirements of seismic design. Provisions related to such requirements are given in Eurocode 8 which complements, and is consistent with Eurocode 6. Numerical values of the actions on buildings and civil engineering works to be taken into account in the design are not given in Eurocode 6. They are provided in Eurocode 1. The basis for the design of buildings and civil engineering works in masonry is given in this Part 1-1 of Eurocode 6, which deals with unreinforced masonry and reinforced masonry where the reinforcement is added to provide ductility, strength or improve serviceability. The principles of the design of prestressed masonry and confined masonry are given, but application rules are not provided. This Part is not valid for masonry with a plan area of less than 0,04 m2. For those types of structures not covered entirely, for new structural uses for established materials, for new materials, or where actions and other influences outside normal experience have to be resisted, the principles and application rules given in this EN may be applicable, but may need to be supplemented. Part 1-1 gives detailed rules which are mainly applicable to ordinary buildings. The applicability of these rules may be limited, for practical reasons or due to simplifications; any limits of applicability are given in the text where necessary. The following subjects are dealt with in Part 1-1: - section 1 : General; - section 2 : Basis of design; - section 3 : Materials; - section 4 : Durability; - section 5 : Structural analysis; - section 6 : Ultimate Limit State; - section 7 : Serviceability Limit State; - section 8 : Detailing; - section 9 : Execution.

  • Standard
    115 pages
    English language
    sale 10% off
    e-Library read for
    1 day

TC - Modifications from EN 1998-3:2005/AC:2010 on the English mother reference version regarding the "National annex for EN 1998-3", Clauses 2 and 4 and Annexes A, B and C + New modifications in Annex A.

  • Corrigendum
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Complementary to Eurocodes 1 to 7 and 9. Additional provisions for the structural design of buildings and civil engineering works to be constructed in seismic regions where risk to life and/or risk of structural damage are required to be reduced. General requirements and rules for assessment of seismic actions and combinations with other actions. General rules for earthquake resistant design of buildings and specific rules for buildings and elements constructed with each of the various structural materials.

  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

TC - Modifications to "National annex for EN 1991-1-2", 1.6, Annex A, B.2, B.4.1 and B.4.2.

  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day

EN 1991 provides general principles and actions for the structural design of buildings and civil engineering works including some geotechnical aspects and shall be used in conjunction with EN 1990 and EN 1992-1999. EN 1991 also covers structural design during execution and structural design for temporary structures. It relates to all circumstances in which a structure is required to give adequate performance. EN 1991 is not directly intended for the structural appraisal of existing construction, in developing the design of repairs and alterations or for assessing changes of use. EN 1991 does not completely cover special design situations which require unusual reliability considerations such as nuclear structures for which specified design procedures should be used.

  • Corrigendum
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

(1) Part 3 of EN 1991 specifies imposed loads (models and representative values) associated with cranes on runway beams and stationary machines which include, when relevant, dynamic effects and braking, acceleration and accidental forces.
(2) Section 1 defines common definitions and notations.
(3) Section 2 specifies actions induced by cranes on runways.
(4) Section 3 specifies actions induced by stationary machines.

  • Corrigendum
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

EN 1991-1-6 provides principles and general rules for the determination of actions which should be taken into account during execution of buildings and civil engineering works.
NOTE 1 : This Part of EN 1991 may be used as guidance for the determination of actions to be taken into account for different types of construction works, including structural alterations such as refurbishment and/or partial or full demolition.  Further guidance is given in Annexes A1, A2 and B.
NOTE 2 : Rules concerning the safety of people in and around the construction site are out of the scope of this European standard. Such rules may be defined for the individual project.
The following subjects are dealt with in Part 1.6 of EN 1991.
Section 1 : General
Section 2 : Classification of actions
Section 3: Design situations and limit states
Section 4 : Representation of actions
Annex A1 : Supplementary rules for buildings (normative)
Annex A2 : Supplementary rules for bridges (normative)
Annex B : Actions on structures during alteration, reconstruction or demolition (informative)
EN 1991-1-6 also gives rules for the determination of actions which may be used for the design of auxiliary construction works as defined in 1.5, needed for the execution of buildings and civil engineering works.
NOTE  Design rules for auxiliary construction works may be defined in the National Annex or for the individual project. Guidance may be found in the relevant European standards. For example, design rules for formworks and falseworks are given in EN 12812.

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Complementary to Eurocodes 1 to 7 and 9. Additional provisions for the structural design of buildings and civil engineering works to be constructed in seismic regions where risk to life and/or risk of structural damage are required to be reduced. General requirements and rules for assessment of seismic actions and combinations with other actions. General rules for earthquake resistant design of buildings and specific rules for buildings and elements constructed with each of the various structural materials.

  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

TC - Modifications to "National annex for EN 1991-1-2", 1.6, Annex A, B.2, B.4.1 and B.4.2.

  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day

TC - Modifications to the National Annex, 1.1, 4.2, 4.6 and A.2.4.

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day

CEN/TC 250 - Modifications in Sections 1 and 2.

  • Corrigendum
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

CEN/TC 250 - Editorial modifications to 1.2, 2.5, 5.2.1.1, 5.2.2.2, 5.2.2.3, 6.1.2 and Annex C.

  • Corrigendum
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1.1   Scope of Eurocode 6
(1)P Eurocode 6 applies to the design of buildings and civil engineering works, or parts thereof, in unreinforced, reinforced, prestressed and confined masonry.
(2)P Eurocode 6 deals only with the requirements for resistance, serviceability and durability of structures. Other requirements, for example, concerning thermal or sound insulation, are not considered.
(3)P Execution is covered to the extent that is necessary to indicate the quality of the construction materials and products that should be used and the standard of workmanship on site needed to comply with the assumptions made in the design rules.
(4)P Eurocode 6 does not cover the special requirements of seismic design. Provisions related to such requirements are given in Eurocode 8 which complements, and is consistent with Eurocode 6.
(5)P Numerical values of the actions on buildings and civil engineering works to be taken into account in the design are not given in Eurocode 6. They are provided in Eurocode 1.
1.1.2   Scope of Part 1-1 of Eurocode 6
(1)P The basis for the design of buildings and civil engineering works in masonry is given in this Part 1-1 of Eurocode 6, which deals with unreinforced masonry and reinforced masonry where the reinforcement is added to provide ductility, strength or improve serviceability. The principles of the design of prestressed masonry and confined masonry are given, but application rules are not provided. This Part is not valid for masonry with a plan area of less than 0,04 m2.
(2) For those types of structures not covered entirely, for new structural uses for established materials, for new materials, or where actions and other influences outside normal experience have to be resisted, the principles and application rules given in this EN may be applicable, but may need to be supplemented.
(3) Part 1-1 gives detailed rules which are mainly applicable to ordinary buildings. The applicability of these rules may be limited, for practical reasons or due to simplifications; any limits of applicability are given in the text where necessary.
(4)P The following subjects are dealt with in Part 1-1:
-   section 1 : General;
-   section 2 : Basis of design;
-   section 3 : Materials;
-   section 4 : Durability;
-   section 5 : Structural analysis;
-   section 6 : Ultimate Limit State;
-   section 7 : Serviceability Limit State;
-   section 8 : Detailing;
-   section 9 : Execution;
(5)P Part 1-1 does not cover:
-   resistance to fire (which is dealt with in EN 1996-1-2);
-   particular aspects of special types of building (for example, dynamic effects on tall buildings);
-   particular aspects of special types of civil engineering works (such as masonry bridges, dams, chimneys or liquid retaining structures);
-   particular aspects of special types of structures (such as arches or domes);
-   masonry where gypsum, with or without cement, mortars are used;
-   masonry where the units are not laid in a regular pattern of courses (rubble masonry);
-   masonry reinforced with other materials than steel.
1.2   Normative references
1.2.1   General
(1)P This European standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to, or revisions of, any of these publications apply to this European standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments).

  • Standard
    115 pages
    English language
    sale 10% off
    e-Library read for
    1 day

EN 1999 applies to the design of buildings and civil engineering and structural works in aluminium. It complies with the principles and requirements for the safety and serviceability of structures, the basis of their design and verification that are given in EN 1990 - Basis of structural design. EN 1999 is only concerned with requirements for resistance, serviceability, durability and fire resistance of aluminium structures. Other requirements, e.g. concerning thermal or sound insulation, are not considered. EN 1999 is intended to be used in conjunction with: - EN 1990 "Basis of structural design" - EN 1991 "Actions on structures" - European Standards construction products relevant for aluminium structures - EN 1090-1: Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components5 - EN 1090-3: Execution of steel structures and aluminium structures - Part 3: Technical requirements for aluminium structures5 EN 1999 is subdivided in five parts: EN 1999-1-1 Design of Aluminium Structures: General structural rules. EN 1999-1-2 Design of Aluminium Structures: Structural fire design. EN 1999-1-3 Design of Aluminium Structures: Structures susceptible to fatigue. EN 1999-1-4 Design of Aluminium Structures: Cold-formed structural sheeting. EN 1999-1-5 Design of Aluminium Structures: Shell structures.

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Eurocode 2 applies to the design of buildings and civil engineering works in plain, reinforced and prestressed concrete. It complies with the principles and requirements for the safety and serviceability of structures, the basis of their design and verification that are given in EN 1990: Basis of structural design.

  • Corrigendum
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day

(1)P This Part 1-2 of EN 1996 deals with the design of masonry structures for the accidental situation of fire exposure, and is intended to be used in conjunction with EN 1996-1-1, EN 1996-2, 1996-3 and EN 1991-1-2. This part 1-2 only identifies differences from, or supplements to, normal temperature design.
(2)P This Part 1-2 deals only with passive methods of fire protection. Active methods are not
covered.
(3)P This Part 1-2 applies to masonry structures which, for reasons of general fire safety, are required to fulfil certain functions when exposed to fire, in terms of:
- avoiding premature collapse of the structure (load bearing function)
- limiting fire spread (flames, hot gases, excessive heat) beyond designated areas (separating function)
(4)P This Part 1-2 gives principles and application rules for designing structures for specified requirements in respect of the aforementioned functions and levels of performance.
(5)P This Part 1-2 applies to structures, or parts of structures, that are within the scope of EN 1996-1-1, EN 1996-2 and EN 1996-3 and are designed accordingly.
(6)P This Part 1-2 does not cover masonry built with Natural Stone units to EN771-6
(7)P This Part 1-2 deals with the following:
- non-loadbearing internal walls.
- non-loadbearing external walls.
- loadbearing internal walls with separating or non-separating functions.
- loadbearing external walls with separating or non-separating functions.

  • Corrigendum
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day

General rules for the structural design of buildings and civil engineering works in reinforced and prestressed concrete made with normal and lightweight aggregates, plain or lightly reinforced concrete and precast concrete for the design of reinforced concrete components with unbonded tendons.

  • Corrigendum
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day

TC - Modifications to the English mother version to the Foreword, to Clauses 1, 2 and 5 and to Annexes B, C and D.
2013: Originator of XML version: first setup pilot of CCMC in 2012

  • Corrigendum
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day

TC - Modifications in the English mother reference version to the Table of Contents, Clauses 1, 4, 5 and Annexes A, B, D, E, F, I, J, K and X.

  • Corrigendum
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

TC - Modifications to the E reference version of the amendment EN 1990:2002/A1/2005 and containing the modifications of the replaced corrigendum EN 1990:2002/A1:2005/AC:2008: modifications to many clauses and subclauses and addition of a new Annex A2 in EN 1990:2002.

  • Corrigendum
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day